skip to main content

Brodit 2 part solution

Home > Car Phone Holder > TomTom > GO 730 T > Holders > Holder with Pass-Through Connector

Holder with Pass-Through Connector view larger image

Holder with Pass-Through Connector for TomTom GO 730 T

Active holder for fixed installation. With tilt swivel. 12/24 Volt. With TMC connectivity (MiniUSB plug).

For TomTom GO 730 T in all countries. (Item # 279024)

Brodit special order product, please contact us for details.

Active holder with pass-through connector and for fixed installation. All cables that can be used with the GPS device can also be used with the holder, for example a TMC cable. This means that you can have both charging and TMC connected to the GPS in the same time! When you have attached the cable to the holder it is firmly in place and you do not have connect it manually to the device each time you put the GPS in the holder. Fits TMC with miniUSB connector (TMC not included).

The holder has a straight cable with open end for fixed installation. The cable is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior.

You can easily take the device with you when leaving the vehicle. 12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Attach onto a ProClip Mounting Platform.

Charging specifications:
Input voltage: DC/10-30V
Charging voltage: DC/4.75-5.3V
Output current(Typ): 2.0A
Input & output protection: Input polarity reversal/Output over voltage/Output over current/Output short protection
LED charging indicator: Power input indicator(Green) , Ovp/Ocp/Output Short(Red)
Operating temperature: 0C ~ +40C
Storage temperature: -20C ~ +80C
RoHS compliant: ROHS


Also Suitable for:
For TomTom GO 520 in all countries.
For TomTom GO 520 T in all countries.
For TomTom GO 530 in all countries.
For TomTom GO 530 T in all countries.
For TomTom GO 630 in all countries.
For TomTom GO 630 T in all countries.
For TomTom GO 720 in all countries.
For TomTom GO 720 T in all countries.
For TomTom GO 730 in all countries.
For TomTom GO 730 T in all countries.
For TomTom GO 920 in all countries.
For TomTom GO 920 T in all countries.
For TomTom GO 930 in all countries.
For TomTom GO 930 T in all countries.
For TomTom WORK GO 7000 in all countries.


Installation Instructions

Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot!

Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.

Installation of the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate on desired position. Screw the attaching plate into place with the enclosed screws. 3. Place the holder over the attaching plate so the tilt swivel fits. Screw the holder onto the attaching plate. All cables that fit the device can be attached to the holder. 4. The holder is in place.

Holder with Pass-Through Connector Holder with Pass-Through Connector Holder with Pass-Through Connector Holder with Pass-Through Connector