skip to main content

Brodit 2 part solution

Home > Brodit Step 1 > Huawei > MediaPad T3 8.0 > Holders > Active holder for fixed installation

Active holder for fixed installation view larger image

Active holder for fixed installation for Huawei MediaPad T3 8.0

With tilt swivel, with Molex adapter system.

For Huawei MediaPad T3 8.0 in all countries. (Item # 513990)

£87.99 inc. VAT

In Stock: 1 | Click to check lead time

1 available from our UK warehouse, order before 15:30 Mon-Fri for same day despatch (excluding holidays).
0 on order currently in transit from manufacturer.
More available to order with a lead time of 7-10 working days.

A bulk discount could be offered on any business order of 25+ pieces. For more details contact us.

Use an active holder for your MediaPad M3 while driving and you will always have a freshly charged battery! The active holder is to be connected inside the dashboard. It provides a discreet and neat installation without any cables hanging over the interior. Safe and convenient!
 
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended.
 
The holder is mounted onto a tilt swivel so you can adjust the angle and switch between portrait and landscape mode.
 
Tablets should not be installed onto a car’s dashboard if they block the view or block key controls. The ProClip is designed for installation of smaller devices (phones), not for large devices (tablets). If you want to place a tablet onto the car’s dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the ProClip is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations.
 
An installation of a tablet onto a vehicle’s dashboard is always done on the customer’s own responsibility. Brodit recommends to use tablets on the car’s headrest, installed onto a Brodit headrest mount.
 
Charging specifications:
Input voltage: DC/10-30V
Charging voltage: DC/4.75-5.3V
Output current(Typ): 2.0A
Input & output protection: Input polarity reversal/Output over voltage/Output over current/Output short protection
LED charging indicator: Power input indicator(Green), Ovp/Ocp/Output short(Red)
Operating temperature: 0°C ~ +40°C
Storage temperature: -20°C ~ +80°C
RoHS compliant: ROHS


Also Suitable for:
For Huawei MediaPad T3 8.0 in all countries.


Installation Instructions

Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. Installation of the holder:
Please read all of the instructions and look at the pictures before attaching the holder. 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate onto the desired position. 3. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted. 4. The holder is in place in upright and horizontal position.

Active holder for fixed installation Active holder for fixed installation Active holder for fixed installation Active holder for fixed installation