skip to main content

Brodit 2 part solution

Home > Brodit Step 1 > AT&T > Samsung Galaxy S III (SGH-i747) > Holders > Active holder for fixed installation

Active holder for fixed installation view larger image

Active holder for fixed installation for AT&T Samsung Galaxy S III (SGH-i747)

With tilt swivel, with Molex adapter system. 2A charger. Fits for devices with skin.

For AT&T Samsung Galaxy S III (SGH-i747) in USA. (Item # 513409)

£109.99

Special order item, lead time from manufacturer is 7-10 working days.

A bulk discount could be offered on any business order of 25+ pieces. For more details contact us.

An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!

You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).

12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended.

The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Fits devices with skin. Attach onto ProClip Mounting Platform.

Charging specifications:
Input voltage: DC/10-30V
Charging voltage: DC/4.75-5.3V
Output current(Typ): 2.0A
Input & output protection: Input polarity reversal/Output over voltage/Output over current/Output short protection
LED charging indicator: Power input indicator(Green), Ovp/Ocp/Output short(Red)
Operating temperature: 0C ~ +40C
Storage temperature: -20C ~ +80C
RoHS compliant: ROHS


Also Suitable for:
For AT&T Samsung Galaxy S III (SGH-i747) in USA.
For Samsung Galaxy S III (AT&T SGH-i747) in USA.
For Samsung Galaxy S III (Sprint SPH-L710) in USA.
For Samsung Galaxy S III (T-Mobile USA SGH-T999) in USA.
For Samsung Galaxy S III (Verizon SCH-i535) in USA.
For Samsung Galaxy S III i9300 in Europe.
For Samsung Galaxy S III i9305 in all countries.
For Samsung Galaxy S4 GT-I9505 in all countries.
For Samsung Galaxy S4 GT-I9506 in all countries.
For Sprint Samsung Galaxy S III (SPH-L710) in USA.
For T-Mobile Samsung Galaxy S III (SGH-T999) in USA.
For Verizon Samsung Galaxy S III (SCH-i535) in USA.


Installation Instructions

Please read all of the instructions and look at the pictures before attaching the holder. Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters. Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. Attaching the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted. 3. To place the device in the holder: Place the upper part of the device in the holder, then press the device forwards and upwards so it snaps into place in the holder. To remove the device from the holder: Press upwards on the lower part of the device, in the same time pull the the device out and down from the holder. 4. The holder is in place.

Active holder for fixed installation Active holder for fixed installation Active holder for fixed installation Active holder for fixed installation